Uwatec X-Tek Especificações

®X-Tek

9English! WARNING DO NOT DIVE with a BC that is damaged, leaks air, or does not function properly. Terminate any dive as safely and qui

10X-TEK FORM TEK SYSTEMNever before you can dive more comfortable with a heavy double tank.Harness system can be optionally equipped with a QR- Weight

11EnglishThread Guide: PRO HARNESS SYSTEM 1. Place the webbing with the hole aligned onto the center rear of the backplate. Depending of height of yo

124. Attach the right shoulder pad by threading the strap through the top pad loop. Make sure that the webbing is on the outside of the pad. (The exa

13English8. Thread the end of the strap through the second loop. a. b.9. Thread the second three bar slide between the second and the third loop,

1411. Thread the webbing through all loops of the left shoulder pad. Make sure that the webbing is on the outside of the shoulder pad. 12. Thread the

15English a. b. c. d. e. f. g. h.

16 i. j. k. l.15. Thread the end of the webbing through the top of the three bar slide (see 10). a. b. c.16. Snap the quick release buckle tog

17English17. Thread the end of the webbing for the bottom left strap from the inside out through the inner slot.18. Thread a three bar slide to the we

1819. Thread a three bar slide about 4 inches (10cm) away from the front of the backplate.20. Thread a at D-ring up to the three bar slide and then l

1EnglishTABLE OF CONTENTSEnglishIMPORTANT WARNINGS ...

19English22. Thread the right end of the webbing in the same manner as described in step 18 on Page 16. a. b. c. d. e.

2023. Attaching the crotch strap: Place the inverted plate on a table, so that you can see the backside of the plate. Place the crotch strap in front

21English25. Thread the other end of the crotch strap with the loop on the waistband.! WARNING When using a weight belt with the crotch strap you

223 Thread the ends of the webbing through the top horizontal slits of the front through the backplate. a. b. c. front view rear view rear vie

23English6. Thread the left end of the webbing from the inside out through the inner slot.7. Thread a three bar slide to the webbing and thread the

248. Thread a three bar slide to about 4 inches (10cm) from the front of the backplate.9. Thread a at D-ring up to the three bar slide and then lea

25English c. d. e. f. g.

2611. Thread the right side of the webbing as described in steps 6, 7 & 8 on Pages 22 & 23. a. b. c. d. e. f. g. h. i.

27EnglishAdjustment: FORM HARNESS SYSTEMYou have the option to position the shoulder straps at the Form Harness System in different ways:1. Thread th

28 g. h. i.2. Thread the strap with the stainless steel buckle outward, in order to position the shoulder straps on the outside. a. b. c. d.

2This information is for your safety. Please read the entire instruction manual before using your X-TEK buoyancy compensator and equipment for the rs

29English e. f. g. h.3. To widen the placement of the straps you can adjust them to the desired position. Use the same instructions as described

30Thread Guide: SOFT TRAVEL BACK PACKSuper Cinch Tank Strap:1. Set the soft backplate in front of you, so you see the loops. Unthread the D-ring and

31English4. Thread the plastic stopper rst and then add the D-ring. a. b. c. view up view sideThread guide: SINGLE TANK ADAPTERRemove the D-ri

321. Place the backplate so it is facing down and then place the bladder onto the backplate. a. b.2. Place the single tank adapter on the bladder

33EnglishAttachment: SOFT BACKPLATE ON X-TEK FORM HARNESS! WARNING Check the tightness of the screws and nuts before each dive. The syst

34ADJUSTING THE SYSTEM:! WARNING Adjust the BC so that it does not restrict your breathing when fully inated. Restriction of normal breathing while w

35English4. To perform the next setting, thread the end of the straps as described in Point 7 at Page 22.5. Pull on the system and grasp with the ar

36TRANSPORT OF THE X-TEK SYSTEMS:Handle the XTEK systems in such a way to ensure that no sharp or heavy objects (e.g. knives, bottles, lamps, lead etc

37EnglishGENERAL SPECIFICATIONSShelf life:Shelf life is seven years for a new, unused BC when deated and stored in a sealed container or bag at typic

38AppendixAttachment: CLAMPS FOR TWIN TANKS1. Put the clamps onto the double tank. (The setting of the clamps for the tank bottles, as described on p

3English! WARNING In accordance with European standards, our BCs can only be considered certied where all components are present, as per the original

39English Adjustment of the bands on the double tanks:For setting the bands on the double tanks, you should note the following:• Attach the bands to

40Procedure:1. Set the tanks parallel, the valves showing in one direction.2. Screw the connector manifold into a valve. The space between A and B,

41EnglishThe following accessories are available through an authorized SCUBAPRO dealer:Item Number Description 23802000 X-TEK Single Tank Adapter

42Test according to DIN EN 1809:1998-1 BuoyancyNotied body 0299 BG Bau, Arbeitsschutzzentrum Haan, Zentrum fuer Sicherheitstechnik, Zwengenb

SUBSIDIARIESSCUBAPROASIA PACIFIC1208 Block A, MP Industrial Center18 Ka Yip St.Chai Wan - Hong KongSCUBAPRO GERMANY Johnson Outdoors Vertriebsgesellsc

P/N 45.021.005 • 10/2010 • 59681010®

46. The content of this manual is based upon the latest information available at the time of going to print. SCUBAPRO reserves the right to make chan

5EnglishThe weights are inserted into the weight pocket (Picture2)The weight pockets are pushed into the weight pockets system (Picture 3+4) and held

6VALVE SET UPSCUBAPRO X-TEK BC´s are completed by the BPI System(Balance Power Inator). It is possible to change the SCUBAPRO Balance Power Inator

7EnglishDeating the BC with the Manual Dump Valve(For Units tted with the SCUBAPRO Manual Dump Valve)Stop and assume an upright position in the wate

8! WARNING Never breathe from the BC. Your BC may contain gas residue, liquid, or contamination that may result in injury or death if inhaled.Keep w